Wallpaper inside corner

How to Wallpaper Corners - dummies

Updated: 01-24-2017

Home Decorating For Dummies

Explore Book Buy On Amazon

Hanging wallpaper is a good do-it-yourself project, but wallpapering corners to make them look perfect can be a challenge. Get great results on wallpapering inside and outside corners by following these tips for a professional finish.

Wallpapering inside corners

Never wrap wallpaper more than 1⁄2 inch around an inside corner with a drop. Even if the walls are perfectly plumb, the paper will pull away from the corner as it dries, making it vulnerable to tearing or wrinkling. Instead, make a wrap-and-overlap seam.

(l.) and out-of plumb outside corners (r.)."/>

Use a wrap-and-overlap seam at inside (l.) and out-of plumb outside corners (r.).

Use a wrap-and-overlap seam for out-of-plumb outside corners, by following these steps:

As you reach the last strip before a corner, measure and cut the strip lengthwise so that it wraps the corner about 1⁄2 inch.
Hang the strip but peel it back from the corner a few inches.
Using a vertical guideline that’s about 1⁄8 inch farther from the corner than the narrowest width of the cutoff, apply the next drop on the adjacent wall, allowing it to wrap the corner.
After you smooth the second drop into place, trim it at the corner with a breakaway razor knife guided by a metal straightedge.
Toss the trimmed paper and peel the paper back from the corner enough to enable you to reposition the first drop.
With the first drop wrapping the corner and smoothed into place, smooth the second drop over the first.

Smooth the paper with a side-arm seam roller, which has no frame on one side of the roller so that you can get into corners with it.

Wallpapering outside corners

Outside corners present two problems. First, because they physically stand out, people often brush against or bang into them.

And second, because outside corners stand out in the sense that they’re eye-catching, you want things in such a position to look as nice as possible. For these reasons, avoid placing a seam right at the corner where it may be brushed apart or may be more noticeable.

If the corner is perfectly plumb, you can just round it. If it’s out-of-plumb, you can use the wrap-and-overlap technique as described in the preceding, but with two differences.

Instead of wrapping the first drop about 1⁄2 inch (Step 1), wrap the corner at least 3 inches to ensure that it stays put.
Instead of having the second drop end right at the corner (Step 4), measure, cut, and position it so that it stops about 1⁄4 inch shy of the corner.

Both cuts are located by measurement and made on the cutting table, not in place.

Making cuts along the length of wallpaper is usually done with a special (read: expensive) 6-foot-long magnesium-alloy straightedge. As a substitute, you can use a 4-inch-wide strip of 1⁄4-inch plywood. If you don’t own a table saw, ask your lumber store to cut the plywood for you.

Cutting wallcovering dulls blades quickly. Snap off dull blades on a breakaway razor or change blades often on another type of cutter.

About This Article

This article can be found in the category:

Walls & Painting ,

5 steps for getting pro results |

(Image credit: Alamy)

Wallpapering a corner requires a whole new level of skill than just tackling a flat wall. Precise cornering isn't difficult, but it does require certain techniques and know-how to get right.

Ideally, you’ll have mastered how to wallpaper a flat wall, starting with the first wallpaper length 20in (50cm) from the left-hand corner of the wall, and keeping going until you reach the righthand corner of the wall. Once there, our step-by-step instructions below for how to wallpaper a corner will be vital to realizing your wallpaper ideas.

How to wallpaper a corner

As you approach a corner, measure the distance to the corner from the last piece of hung wallpaper and add on 1in (2.5cm) to allow for an overlap. Trim the next piece of wallpaper to this width, but don’t throw away the remaining cut paper.

1. Hanging the trimmed wallpaper against the corner

‘Hanging wallpaper does not have to be complicated,’ says Kirsty Mole, Decorative Home Category Manager at B&Q . ‘Position the trimmed piece carefully from the top, and once you’re happy, hang it, using a wallpaper smoothing tool or brush to smooth it towards and into the corner.’ The excess wallpaper will overlap onto the adjoining wall. Trim the paper at the top and bottom in the usual way.

2. Set a plumb line for the adjacent wall

Although you could live a whole life under the illusion that walls are straight and at right angles any self-respecting tradesperson will tell you (at tedious length), that’s not the case. So you’ll need to set a plumb line again on the new wall. Measure the width of your wallpaper offcut. Now measure this distance from the corner and make a mark high up on the wall. To find the vertical, use a weight attached to a length of string and hold it against the mark. Now use the string as a guide to make marks at intervals on the wall with a pencil.

3. Hang wallpaper on the adjacent wall

This is easy. Simply hang the offcut against the plumb line and it should fit neatly into the corner, overlapping the first piece. Now you’re done but there is a neater way the professionals tackle it. ‘For a professional finish you should take a knife, such as a Stanley knife, with an extremely sharp, fresh blade and using a steel straight edge cut the papers where they overlap,’ says James Greenwood, Wallpaper Specialist at Graham & Brown . ‘Remove any excess from the top paper, then peel the top paper back and remove the excess from the bottom paper. Now push the top paper down and it should match and meet perfectly with the bottom paper, joining like two regular wallpaper seams. ’

4. Tackling an external corner

If you come up against an external corner, cut the wallpaper to fit as for an internal corner, allowing for an overlap in the same way. Smooth the wallpaper into place around the corner. Just as for internal corners, you’ll need to make a new plumb line on the adjacent wall before continuing.

5. Wallpaper the corner of a chimneybreast

If the wall has a fireplace, this is the focal point and is the place to start, placing the first piece of wallpaper on the chimneybreast centrally and working outwards. ‘This ensures the design is centred and aligns well with the focal point,’ says James. As you reach the external corner, smooth the paper onto the fireplace wall and make a cut at the top of the wallpaper where it meets the corner, so that you can ease the paper around the corner. Smooth it into place. ‘The wrapped portion may not hang ‘true’ but the overlap will not be in sight.’ Cut a new piece to complete the reveal, allowing an overlap for the internal corner.

Do you overlap wallpaper in corners?

When wallpapering an inside or outside corner, wrap no more than an inch around the corner. Then, with the next drop, overlap the piece you have wrapped around the corner with the next drop by 1⁄2 an inch.

Lola Houlton is H&G's long-term intern. Currently student of Psychology at the University of Sussex, she began writing content for Real Homes around the subjects of children's and teenagers' bedroom, in particular covering the psychology of teens and their approach to tidiness. From there, Lola expanded her knowledge of a broad range of subjects and now writes about everything from organization through to house plants while continuing her studies.

how to stick wallpaper in the corners of a room, how to glue the corners with non-woven wallpaper

Method #1.

Using the rule or a metal profile and a plumb line, find the most protruding point of the adjacent wall. It is important that the profile fits snugly against the wall and must be held strictly vertically.

Angle trowel must be applied to the found point, and a profile must be applied to the trowel. With a plumb line, check that the profile is strictly in a vertical position, then notches for dowels are made on the wall.

After that, using a puncher, drill holes in the wall, install dowels and fix the profile with self-tapping screws.

The next step is to apply the putty on the corner pre-moistened with water. With the help of an angled spatula, putty is applied and an even angle is formed, excess gypsum must be removed.
When the layer of putty dries, it is sanded with zero sanding paper.

Method #2.

A special metal or plastic perforated corner is installed in the corner, to the edges of which a mesh is attached. Contrashults are mounted strictly vertically and fixed with a putty applied to the mesh. When the putty dries, it must be sanded.

Using these leveling methods will help prepare a perfectly level surface for wallpapering in corners.

How to glue wallpaper in the corners

When wallpapering, you will inevitably encounter the need to paste inside and possibly outside corners. The choice of pasting method is influenced by the type of corner, and not by the type of wallpaper. It is worth noting that the methods below are applicable only for plain wallpapers.
Let's find out how to paste wallpaper in the corners of the room.

External corners

Modern interiors rarely have external corners, mostly internal ones. But if you still have to paste the outer corner, then recommendations on how to glue the outer corner with wallpaper will surely be useful.

Sewing sequence for outside corner:

Coat the wallpaper strip and the surface to be pasted with glue.
Glue the trellis to the wall and align carefully. This is necessary to remove air gaps.
Bend the strip to the other side of the corner. If wrinkles form on the surface, then you can make a small incision.
Set aside 0.5 cm from the edge and make a strictly vertical marking using a plumb bob and a pencil.
Apply glue to the next sheet and stick it overlapping, making sure to line it up first.
Using a guide, cut through the middle of the joined sheets with one cut.
Remove the cut strips and roll the seam with a rubber roller.

Internal corners

The width of the sheet should exceed the width of the wall at the connection point with an angle of 2-4 cm. Then the sheet is glued and a vertical strip is drawn on the strip at a distance of 5 mm.

The edge of the next sheet must match the vertical line when pasting. In cases where the seam is invisible, you can proceed to further pasting the walls. If the seam protrudes, make a cut and make it end-to-end, removing the extra strips.

Measure the distance from the edge of the last sheet to the angle above and below.

The difference can reach several centimeters.

Mark points on the spread sheet with a pencil or small cuts. It is important to make a note where the top or bottom is.

Add 5 cm to the measurements obtained and cut off a piece of wallpaper to the required width.

Dock the wallpaper sheet with the cut sheet and lay it overlapping, overlapping the minimum point from our measurement.

The part that overlapped the marks needs to be cut off. Cut the sheet to length.

Coat the sheet with wallpaper paste and glue it end-to-end with the last sheet, glue it on at the final stage. It is necessary to exclude the formation of folds by working the corner and the seam.

We draw with the help of a plumb line several vertical lines, at a distance from the corner to the edge of the sheet. The step between the lines is 5 mm.

Coat the next sheet with glue and fold it for impregnation.

Glue the canvas in such a way that the central pattern fits perfectly. We glue the wallpaper, smoothing it to the side of the corner, focusing on the vertical lines.

Cut the jointed parts according to the resulting overlap, using a metal profile and a sharp knife.

Remove excess strips and roll the joint with a rubber roller.

How to glue non-woven wallpaper in the corners

However, it is necessary to take into account a number of nuances when pasting walls with this type of wallpaper.

Do not try to cover both sides of the corner with one sheet. There is a possibility of wrinkles.
Non-woven wallpapers are always glued end-to-end.
When gluing non-woven wallpaper, the adhesive should only be applied to the wall.

How to fix the joints in the corners

Quite often there are situations when, after gluing the wallpaper, the joints between them become visible. Let's find out how to close the corners of the walls after gluing the wallpaper so that the joints are not visible.

Checkered or striped pattern easily hides seams, even if they are visible. Joints will be noticeably visible on plain wallpaper.

If you plan to paint the wallpaper, then the joint at the corners can be masked with a special sealant, which can be painted in the color of the wallpaper.

Often seams occur on paper wallpapers. To avoid this, they must be glued immediately after applying the adhesive. Otherwise, there will be a shrinkage of the canvases and gaps cannot be avoided.

Corner joints can be grouted for tiles of the same colour. You can also use a marker or pencil.

To make the wallpaper more attractive and hide the joint at the corners of the wallpaper, moldings or special panels will help, a more budget option is paper borders.

Technology for working with uneven corners

Here are some tips on how to glue wallpaper in uneven corners.

Buy wallpaper with a neutral pattern that does not require docking at the edges of the panel. The picture probably does not match, which will look very unaesthetic.
Give preference to wallpaper on a non-woven base, as they stretch perfectly, do not get wet, do not tear and are able to hide minor wall defects.
Use a little trick - glue the uneven corner in two layers. Glue a strip 8-12 cm wide under the main trellis. This is necessary in order to fill the gaps formed when cutting the outer layer.
You can use masking net to reinforce the corner and mask small depressions.
To even out the shoulder, it can be trimmed with a herringbone. The glued overlapping strip hides the cuts.

Oc -to -use of the Yglov

Oklekiyki yogli is not like that.

Treat corners thoroughly with primer. Instead of a special primer, you can use wallpaper glue applied a few hours before the start of work.
Apply the adhesive in the corners with a brush only, this will help avoid unwanted gaps.
Heavy and thick wallpapers are glued with a special transparent glue.
Smooth out the wallpaper in the corners until all air gaps are gone.
Carefully move the edges of the sheets after cutting the seam and coat them with glue, because the adhesive mass will be removed along with the removed trimmings.

step-by-step guide, fit pattern, cutting features

Home
Construction and repair

In the article you can find the answer to the question of how to glue wallpaper in the corners. It is worth taking the finishing process with all responsibility, irregularities can be striking, thereby spoiling the impression of a freshly made repair.

08/27/2018 0

See photo gallery
. .. photo

Step-by-step instructions for gluing inner corners
How to glue an outer corner?
What if the corners are uneven?
Peculiarities of gluing with meter long wallpaper
How to join in corners?
How to adjust the pattern in the corners?
Peculiarities of trimming wallpaper in the corners

How to remove an unpleasant smell from a washing machine at home? How to clean a carpet with your own hands?

Step-by-step instructions for gluing inner corners

When decorating, uneven walls and the resulting creases in the wallpaper can be a major problem. It should also be borne in mind that with curved walls, the joints of the wallpaper can diverge.

After gluing the last sheet in front of the inside corner of the sheet, measure the remaining distance. It is measured from the edge of the glued canvas to the adjacent wall, 10-15 millimeters are added to the resulting figure. If the walls are strongly curved, then the additional figure may be larger.
A strip equal to the resulting figure is cut off, taking into account the allowance.
Surfaces are treated with glue. Depending on the type of coating, this can be only a wall or both surfaces.
The strip is glued with its own cut side to the wall. Wallpaper should go to another plane.
If the pasted wallpaper is wrinkled, make a few small cuts perpendicular to the folds.
Draw a vertical line on an adjacent wall with a level or slope. The distance from the corner is equal to the width of the previous cut strip, excluding additives.
Surfaces are smeared with glue, after which the coating is glued to the wall with a flat side to the marked line. The cut off side goes to the adjacent wall.
If the coating is thick, the wallpaper is cut off along the overlay line.

How to glue the outer corner (outer)?

The protruding corner must be glued in the same way as the inner one, however there are slight differences that must also be taken into account when working.

Measures the distance remaining from the pasted wallpaper to the adjacent wall. 20-25 millimeters are added to the resulting figure.
A segment is cut off, taking into account the added 20-25 millimeters.
Before gluing, the surfaces are treated with an adhesive.
The even edge must be glued to the wallpaper already fixed on the wall, the side cut off by oneself “enters” the adjacent plane.
If necessary, small cuts are made in the place of the wallpaper that overlaps another wall, smoothed and pressed against the wall.
A vertical strip is drawn on an adjacent wall at a distance of the just pasted cut strip plus 6-10 millimeters.
After applying the adhesive, the strip is applied to the wall with its even side to the marked line, going to the edge of the already glued strip.
Joints are smeared with glue and ironed with a roller. After that, the top layer is cut along the ruler and the two layers are joined together.

What if the corners are uneven?

Uneven walls are a common problem in old houses. Before you start gluing the finish coating, it is advisable to carry out preparatory work and bring the surfaces “in order”. If visually the corners are even and do not require major repairs, it will be enough to walk with a hard cloth, removing small bumps and dust. If the irregularities are visible to the naked eye, then it is better to do a little work before you start gluing the wallpaper.

When carrying out work on finishing putty, a plastic corner is inserted and fixed with a putty mixture. They can be purchased at a hardware store.
After drying, the surface is leveled with putty or plaster.
After drying, the walls are treated with a primer.
After the work done on the walls, you can glue the finish.

0022

Wide blades are convenient because they allow you to finish with fewer seams on the surface. Gluing them is more difficult, but the result is worth it.

Most often, meter-long wallpapers are made with a non-woven base and a vinyl coating; they are much easier to glue. However, wide paper products are also found.
When working with non-woven meter products, glue is applied only to the wall.
Wide wallpapers require surface preparation.
For pasting corners, the sheet must be cut into pieces and glued with an overlap. After that, the excess of the top layer is cut off.
After applying the strip to the wall for some time, it remains possible to level the coating by gently moving it.

How to join in corners?

It would seem that such a trifle as gluing the corners in a room can completely spoil the whole work if done incorrectly. And if there is also a pattern on the wallpaper that needs to be customized, then you should approach the finish responsibly.

The strip is glued in such a way that it extends to the adjacent side. The width of the entry should not be more than 5 centimeters.
Use a plastic spatula to level the corner.
The next segment is overlapped.
In order to cut off the excess overlap evenly, a rule is applied to the middle of the overlap and the excess edge is cut off with one movement with a clerical knife. In order for the cut strip to be even, it is worth using a level.

How to adjust the pattern in the corners?

It is important that the pattern is continuous and even around the entire perimeter of the room. To do this, you need to correctly combine the pattern, and cut off the excess.

The strips are also overlapped. Leave an allowance for both walls.
Press the wallpaper against the corner with a plastic spatula.
After gluing the second sheet, the wallpaper is cut according to the pattern. This method applies to wallpaper with a small pattern. For a large pattern, trimming around the edges may be required.

Before gluing, you must first prepare the material for work by spreading the floor covering and studying the pattern. Segments are cut off after selecting the pattern in height.

Peculiarities of cutting wallpaper in the corners

In order to get a perfectly even seam in the corner, you need to trim the excess correctly.

After the wallpaper is glued to the wall, an even metal ruler is applied, it can also be a spatula or a rule. To make the cut line even, you can use the level.
With a sharp clerical knife, cut off the excess along the edge of the ruler, after which the top layer of wallpaper will move away.
Learn more